:?:
Hello folks,
Do any of you use Tu3000 in a 223? I have used it quite extensively over the last couple of years in my 308 @ 600 yards + and it seems very good. I have just brought a 223 for my wife to paper punch with and, if possible would like to use the same powder (I have a few kilos of it!)
The 223 has a 26" 1 in 9 barrel and I will be reloading with 69 grn SMK's
Thanks in advance.
Vectan TU3000
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Re: Vectan TU3000
Meaty,
At the moment I can only find the following reloading information relating to Vectan powders;
http://www.lhs-germany.de/uploads/media/223Rem_01.pdf
At the moment I can only find the following reloading information relating to Vectan powders;
http://www.lhs-germany.de/uploads/media/223Rem_01.pdf
Re: Vectan TU3000
23 grains apparently: http://www.balleurope.com/recharge/epau ... ?langue=en
I can check it with QuickLoad if you can give me a bullet weight and COAL
I can check it with QuickLoad if you can give me a bullet weight and COAL
-
Christel
- Site Admin
- Posts: 17528
- Joined: Fri Nov 05, 2010 7:52 pm
- Location: Wind Swept Denmark
- Contact:
Re: Vectan TU3000
Loads of info here, Meaty.
- Attachments
-
- VihtaVuori01.pdf
- (373.3 KiB) Downloaded 131 times
-
Christel
- Site Admin
- Posts: 17528
- Joined: Fri Nov 05, 2010 7:52 pm
- Location: Wind Swept Denmark
- Contact:
Re: Vectan TU3000
Looking at the PDF I get 20.2 min load and 21.9 max with 69 scenars which should not make a big difference to the SMK's you are using.
BTW that PDF has a burning rate chart.
BTW that PDF has a burning rate chart.
Re: Vectan TU3000
This may be of some use as well, it looks to be the full load data for .223
-
Meaty
Re: Vectan TU3000
Hello all,
Thanks very much for all the info. Should keep me going for a while.
Regards.
Ian.
Thanks very much for all the info. Should keep me going for a while.
Regards.
Ian.
-
richard
Re: Vectan TU3000
If you phone Peterlawman he will send you a vectan cat,very helpfull guy.
Who is online
Users browsing this forum: Bing [Bot], Google [Bot] and 4 guests