This might seem daft, but how can I tell if a LEE die is a neck sizing or Full Length sizing die? Is it to do with the amount of th ecas ethat travels into the die?
:-P :-P
Dies - Stupid Question
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
Mike357
- Posts: 3637
- Joined: Sat Dec 04, 2010 7:25 pm
- Home club or Range: NRA, Bisley, Dundee Rifle & Pistol Club & Bishop Auckland GC
- Location: Near Durham(ish)!
- Contact:
Dies - Stupid Question
It's not the pace of life that concerns me, it's the sudden stop at the end!
-
Tower75
Re: Dies - Stupid Question
Well, with my LEE dies, the full length sizer has a nut at the top of the body that can only be turned with a wrench. The neck sizer, however, has a turn-knob that you can move with your hand.
Not sure if that'll help.
Not sure if that'll help.
Re: Dies - Stupid Question
Lee collet Neck sizing die set
Lee full lentgh rifle die set
-
Dougan
Re: Dies - Stupid Question
Hi Mike - Are there any markings on them? - my RCBS have 'NS' and 'FL' on them.....
-
Mike357
- Posts: 3637
- Joined: Sat Dec 04, 2010 7:25 pm
- Home club or Range: NRA, Bisley, Dundee Rifle & Pistol Club & Bishop Auckland GC
- Location: Near Durham(ish)!
- Contact:
Re: Dies - Stupid Question
No markings on them and the reference numbers don't correspond to anything on the Lee web site.
However from Alpha1's post and further refernce back to the web site I have established that my Lee 303 die is indeed a Full Length sizing die. Am I right in thinking that once all brass has been thru the Enfield I can then just Neck Size only?
However from Alpha1's post and further refernce back to the web site I have established that my Lee 303 die is indeed a Full Length sizing die. Am I right in thinking that once all brass has been thru the Enfield I can then just Neck Size only?
It's not the pace of life that concerns me, it's the sudden stop at the end!
-
Mike357
- Posts: 3637
- Joined: Sat Dec 04, 2010 7:25 pm
- Home club or Range: NRA, Bisley, Dundee Rifle & Pistol Club & Bishop Auckland GC
- Location: Near Durham(ish)!
- Contact:
Re: Dies - Stupid Question
P.S. Cheers for that Rob, see I knew it was a stupid question! 
It's not the pace of life that concerns me, it's the sudden stop at the end!
-
Doz
Re: Dies - Stupid Question
Yep, well it works for me... :)Mike357 wrote: Am I right in thinking that once all brass has been thru the Enfield I can then just Neck Size only?
-
Dougan
Re: Dies - Stupid Question
Yes, as long as it's used in the same rifle. Then just neck sizing gives you a cartridge that fits your rifle...and can improve the accuracy - I've just been neck sizing the PPV I was using in my SMLE, and they fit and shoot nicely.Mike357 wrote:No markings on them and the reference numbers don't correspond to anything on the Lee web site.
However from Alpha1's post and further refernce back to the web site I have established that my Lee 303 die is indeed a Full Length sizing die. Am I right in thinking that once all brass has been thru the Enfield I can then just Neck Size only?
Hope this is better than my previous contribution...
:lol:Who is online
Users browsing this forum: No registered users and 1 guest