As above i need a cheap safe way to cast slug for a 12 bore
any advise on molds and ways of melting lead ?
shotgun slug casting
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
Dellboy
- Full-Bore UK Supporter
- Posts: 2636
- Joined: Wed Aug 31, 2011 11:49 am
- Home club or Range: Star Shooting Club
- Location: Essex
- Contact:
shotgun slug casting
2020 GOOD DEALS WITH
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
-
saddler
Re: shotgun slug casting
Cheap? Lee slug mold or round ball mold. Best? Not the Lee mold....but...
Heat the lead past 325-deg & it'll melt....the Lee lead pots are cheap...other options are available.
Heat the lead past 325-deg & it'll melt....the Lee lead pots are cheap...other options are available.
-
Dellboy
- Full-Bore UK Supporter
- Posts: 2636
- Joined: Wed Aug 31, 2011 11:49 am
- Home club or Range: Star Shooting Club
- Location: Essex
- Contact:
Re: shotgun slug casting
What would you recomend Saddler
2020 GOOD DEALS WITH
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
Re: shotgun slug casting
How cheap and to what standard, are you shooting slug for fun or are you going for groups and long range? Will make a difference in what you cast!
S&W M&P 15-22
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: shotgun slug casting
Lyman sabot slug mould is not too shabby - not cheap though
You'll need the lead and the mould plug (for the hollow base) hot to geta dent fill without wrinkles
You'll need the lead and the mould plug (for the hollow base) hot to geta dent fill without wrinkles
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
25Pdr
Re: shotgun slug casting
A 15MM AF Ring spanner used as a Mold will give you a slug weighing around 400 Grains with a O/D of 0.680".
Hold the spanner on a flat metal surface and dunk in water when it hardens, tap the slug out.
Hold the spanner on a flat metal surface and dunk in water when it hardens, tap the slug out.
Who is online
Users browsing this forum: No registered users and 7 guests