NOE are looking at a run of a modified version of their K31 boolit mould.
Discussion thread is here: http://noebulletmolds.com/smf/index.php ... 172.0.html
K31 boolit mould.
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
dromia
- Site Admin
- Posts: 20226
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
K31 boolit mould.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
kennyc
- Posts: 2340
- Joined: Wed Jul 20, 2011 11:21 pm
- Home club or Range: hunters NRPC
- Location: Reading West Berks
- Contact:
Re: K31 boolit mould.
so is this a "K31" mould or a ".308" mould? as I understand it, if they increase the nose diameter it will cause problems in the K31?
-
dromia
- Site Admin
- Posts: 20226
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: K31 boolit mould.
Depends on the rifle, there were reports of the original being a tad small in some K31s.
This way you will get a mould to fit the larger K31s and work in 308s as well.
It is also easier to size down a nose than bump it up.
Al will no doubt be doing an inventory run of the original so hold on for one of those if that is what fits your rifle.
This way you will get a mould to fit the larger K31s and work in 308s as well.
It is also easier to size down a nose than bump it up.
Al will no doubt be doing an inventory run of the original so hold on for one of those if that is what fits your rifle.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Who is online
Users browsing this forum: Google [Bot] and 9 guests