Welcome to Full-Bore UK
I adjusted my torch right down yesterday and annealed all of my 300aac cases, nice job
Reloader Case Annealer
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
phaedra1106
- Posts: 3393
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Reloader Case Annealer
Hi Lubo
Welcome to Full-Bore UK
I adjusted my torch right down yesterday and annealed all of my 300aac cases, nice job
Welcome to Full-Bore UK
I adjusted my torch right down yesterday and annealed all of my 300aac cases, nice job
There's room for all Gods creatures, next to the mash and gravy :)
-
Pete
- Full-Bore UK Supporter
- Posts: 2973
- Joined: Tue Sep 15, 2015 8:48 am
- Home club or Range: NRA Bisley
- Contact:
Re: Reloader Case Annealer
Apart from the cost, the Amp looks quite a bit slower to use than Lubo's machine, and requires more operator input.
IMHO simplest is best where technology at this level is concerned.
Pete
IMHO simplest is best where technology at this level is concerned.
Pete
"Tantum religio potuit suadere malorum" Lucretius
You're offended? Please explain why your inability to control your emotions translates into me having to censor my opinions....
You're offended? Please explain why your inability to control your emotions translates into me having to censor my opinions....
-
phaedra1106
- Posts: 3393
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Reloader Case Annealer
The Amp is lovely but very expensive!.
Using Lubo's I simply took 2 cases from each of my various calibres, marked them up with Tempilaq and ran one through with the time set on maximum and noted the time needed.
I adjusted the timer then ran the second case through to double check.
I now have a record of the times for each calibre/make of brass and it works very nicely indeed.
I shot 100rnds of 6.5Creedmoor yesterday, this is R P brass and looking at my list it needs 7.5 seconds, so just adjust the timer then start feeding cases through, job done :)
Using Lubo's I simply took 2 cases from each of my various calibres, marked them up with Tempilaq and ran one through with the time set on maximum and noted the time needed.
I adjusted the timer then ran the second case through to double check.
I now have a record of the times for each calibre/make of brass and it works very nicely indeed.
I shot 100rnds of 6.5Creedmoor yesterday, this is R P brass and looking at my list it needs 7.5 seconds, so just adjust the timer then start feeding cases through, job done :)
There's room for all Gods creatures, next to the mash and gravy :)
Re: Reloader Case Annealer
What do you do about repeating the flame intensity/heat each time?
-
phaedra1106
- Posts: 3393
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Reloader Case Annealer
It's a fairly cheap and cheerful torch but I set the flame length by eye and I always run 1 Tempilaq case before doing a batch to be sure.
I ran my second batch of 6.5 Creedmoor through it this morning, timing for the Tempilaq case was what I'd previously noted, 7.5 seconds.
I ran my second batch of 6.5 Creedmoor through it this morning, timing for the Tempilaq case was what I'd previously noted, 7.5 seconds.
There's room for all Gods creatures, next to the mash and gravy :)
-
raptorcalls
Re: Reloader Case Annealer
You are unstoppable nowphaedra1106 wrote:Hi Lubo
Welcome to Full-Bore UK
I adjusted my torch right down yesterday and annealed all of my 300aac cases, nice job
clapclapWho is online
Users browsing this forum: Amazon [Bot], Google [Bot], Majestic-12 [Bot] and 0 guests