kynoch number 81 berdan primers

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Post Reply
Message
Author
User avatar
graphictart
Posts: 94
Joined: Fri Jun 08, 2012 9:07 am
Home club or Range: NRA, Bisley
Location: Berkshire
Contact:
Contact graphictart

kynoch number 81 berdan primers

#1 Post by graphictart »

Hi all,
Does anyone know if Kynoch number 81 berdan primers are corrosive?
All help appreciated.
Attachments
C42FE1F1-929E-4E21-9EAC-C0080EA110A6.jpeg
Top
PeterN
Full-Bore UK Supporter
Posts: 410
Joined: Tue Sep 22, 2020 8:08 am
Contact:
Contact PeterN

Re: kynoch number 81 berdan primers

#2 Post by PeterN »

I use those and they are not corrosive. At least, I treat as non corrosive primers and have had no issues.
Regards
Peter.
Top
User avatar
graphictart
Posts: 94
Joined: Fri Jun 08, 2012 9:07 am
Home club or Range: NRA, Bisley
Location: Berkshire
Contact:
Contact graphictart

Re: kynoch number 81 berdan primers

#3 Post by graphictart »

Hi Peter,
Thank you for the reply.
I don't suppose you know if these would be suitable for .303 as well as 7.62x51?

All help appreciated.
Top
PeterN
Full-Bore UK Supporter
Posts: 410
Joined: Tue Sep 22, 2020 8:08 am
Contact:
Contact PeterN

Re: kynoch number 81 berdan primers

#4 Post by PeterN »

I use these primers for 7.62x51, .303, 7.5x55 Swiss, 7.92x57, .30-06 and 8x56R. They should be OK for any Berdan primed case that takes that size of primer.
Regards
Peter.
Top
User avatar
graphictart
Posts: 94
Joined: Fri Jun 08, 2012 9:07 am
Home club or Range: NRA, Bisley
Location: Berkshire
Contact:
Contact graphictart

Re: kynoch number 81 berdan primers

#5 Post by graphictart »

Hi Peter,
Wonderful news.
Thank you for your time and help.

Regards
Top
User avatar
dodgyrog
Posts: 4103
Joined: Wed Jan 05, 2011 11:17 pm
Home club or Range: Three Counties Sporting Club & Gardners Guns
Location: Consett, County Durham
Contact:
Contact dodgyrog

Re: kynoch number 81 berdan primers

#6 Post by dodgyrog »

Excellent primer if you can find them.
Non corrosice in my experience
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
Top
User avatar
graphictart
Posts: 94
Joined: Fri Jun 08, 2012 9:07 am
Home club or Range: NRA, Bisley
Location: Berkshire
Contact:
Contact graphictart

Re: kynoch number 81 berdan primers

#7 Post by graphictart »

Thanks guys!
Just need some 303 Berdan Brass now.
Top
PeterN
Full-Bore UK Supporter
Posts: 410
Joined: Tue Sep 22, 2020 8:08 am
Contact:
Contact PeterN

Re: kynoch number 81 berdan primers

#8 Post by PeterN »

There were two sealed tins of 5000 number 81 primers in the Holts sealed bid auction that has now ended. I registered to bid on them but thought do I really need another 10,000 primers as I already have 4000 odd Berdan primers. I thought I would leave a low bid so I would get them cheap if no-one else had bid. However, it seems you can't bid lower than the low estimate. I didn't want to spend over £130 on them but tried leaving a minimum bid as a practice bid hoping that someone had bid before me. However, I kept getting an error message of some sort so never got a bid placed. It will be interesting to see what they went for.
Regards
Peter.
Top
Post Reply

Return to “Reloading and Ammunition”

Who is online

Users browsing this forum: No registered users and 2 guests