5.56 nato in .223

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Post Reply
Message
Author
ellmerfudd

5.56 nato in .223

#1 Post by ellmerfudd »

Hi everyone how are you, my question is this has anyone ever actually heard of a gun blowing up due to using 5.56 ammunition in .233 chambered guns, i have read all about it on the internet and the different pressures, and that both are measured in different ways saami etc but loads of lads at my club use surplus 5.56 x45 nato in their remington 700's i just wondered what everyones views on this practice were please
zanes

Re: 5.56 nato in .223

#2 Post by zanes »

SAAMI list it as an "unsafe combination" here:

http://www.saami.org/specifications_and ... ations.pdf

Enough reason for me not to even think about doing it (though I don't currently have a .223). Suspect I could reload for close to the cost per bang of milsurp.
ellmerfudd

Re: 5.56 nato in .223

#3 Post by ellmerfudd »

http://www.luckygunner.com/labs/5-56-vs-223/ this was quite interesting reading, im not planning using 5.56 myself, i was just curious as to the difference and know alot of lads using the nato stuff
Daryll
Posts: 1048
Joined: Sat Jun 14, 2014 9:07 am
Home club or Range: Isle Target Sports Club
Location: Cambridgeshire
Contact:

Re: 5.56 nato in .223

#4 Post by Daryll »

To be honest, pretty much all I use in my Rem 700 and M4 carbine is mil surp 5.56....I think i have 3 different types in my cabinet at the moment, all work fine in both rifles apart from one batch that gives very tight extractions in the M4, but works fine in the Remington... no other signs of excess pressure.
User avatar
snayperskaya
Posts: 7234
Joined: Fri Oct 04, 2013 6:43 pm
Home club or Range: West Bank of the Volga.....
Location: West of The Urals
Contact:

Re: 5.56 nato in .223

#5 Post by snayperskaya »

.223 Saiga rifles for example can use 5.56mm ammunition with no problems as the ".223" stamping on the receiver was more of a marketing move for sporting purposes as the .223 appears more "sporting" than the military sounding 5.56mm.The chamber is actually the same as a 5.56 NATO chambered AK-101.
"The only real power comes out of a long rifle." - Joseph Stalin

Give a man a gun and he can rob a bank.....give a man a bank and he can rob the world!.

More than a vested interest in 7.62x54r!
User avatar
meles meles
Posts: 6335
Joined: Mon Jun 06, 2011 8:17 pm
Home club or Range: HBSA
Location: Underground
Contact:

Re: 5.56 nato in .223

#6 Post by meles meles »

Maybe you should think about having the chamber cut to Wylde specifications, ooman.

The .223 Wylde chamber has the external dimensions and lead angle as found in the military 5.56×45mm NATO cartridge and the 0.2240 inch freebore diameter as found in the civilian SAAMI .223 Remington cartridge. Rifles with a .223 Wylde chamber will accept both .223 Remington and 5.56×45mm NATO ammunition. The case is actually the same in both .223 and 5.56, it's just the chambers that are different between military and civilian rifles. The Wylde chamber shoots the relatively long and heavy 80-grain bullets very well. Have a word with Dave at Valkyrie Rifles...
Badger
CEO (Chief Excavatin' Officer)
Badger Korporashun



Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
saddler

Re: 5.56 nato in .223

#7 Post by saddler »

meles meles wrote:The case is actually the same in both .223 and 5.56, it's just the chambers that are different between military and civilian rifles...
Sort of.
Externally the case IS the same, but they do differ in case wall thickness though.
Andy632

Re: 5.56 nato in .223

#8 Post by Andy632 »

I wouldn't advise using 5.56 nato in a .223 rem. I do however, have no issues with using XM193 or M193 5.56 in a .223 Rem.
Post Reply

Who is online

Users browsing this forum: No registered users and 8 guests