Lee Parts

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Post Reply
Message
Author
25Pdr

Lee Parts

#1 Post by 25Pdr »

Hi,
Needing replacement primer feed for my Lee Loadmaster, Krank out of stock, who's the best to try UK/ Europe or USA.

Cheers...
Top
User avatar
dodgyrog
Posts: 4103
Joined: Wed Jan 05, 2011 11:17 pm
Home club or Range: Three Counties Sporting Club & Gardners Guns
Location: Consett, County Durham
Contact:
Contact dodgyrog

Re: Lee Parts

#2 Post by dodgyrog »

Try Hannams
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
Top
User avatar
dromia
Site Admin
Posts: 20226
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:
Contact dromia

Re: Lee Parts

#3 Post by dromia »

Failing that Titan in the US.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Top
User avatar
phaedra1106
Posts: 3429
Joined: Wed Feb 08, 2012 9:37 pm
Location: Just outside Sacriston (the nice bit!)
Contact:
Contact phaedra1106

Re: Lee Parts

#4 Post by phaedra1106 »

Which exact part is it you're after?, I have 2 Loadmasters and don't use the priming feature on either,

http://leeprecision.com/reloading-press ... s-priming/
There's room for all Gods creatures, next to the mash and gravy :)
Top
25Pdr

Re: Lee Parts

#5 Post by 25Pdr »

Thanks Gentlemen... :good:

Got one from Hannams..Ta

Note to phaedra1106

I was too quick, could have got one of yours. Ta anyway.
Top
the running man
Posts: 2004
Joined: Tue Jun 07, 2011 7:05 am
Home club or Range: Bdrpc ebrpc
Contact:
Contact the running man

Re: Lee Parts

#6 Post by the running man »

phaedra1106 wrote:Which exact part is it you're after?, I have 2 Loadmasters and don't use the priming feature on either,

http://leeprecision.com/reloading-press ... s-priming/
I don't blame u jeff!
When someone says "it's not about the money" you know what? it probably is all about money!
Top
Post Reply

Return to “Reloading and Ammunition”

Who is online

Users browsing this forum: No registered users and 9 guests