Hi,
Someone on here (can't remember who, sorry) gave me some advice on what size and type of shell house bullets (cast) to use on my Handi Rifle (.308).
So I after that gentleman (or lady) to stand up and make their self known again please. Tried casting my own with a Lee mould and too be fare they're not all coming out consistently good, so its a waste of time IMHO. I would also get a good working knowledge of how accurate the rifle is.
Thanks
Rob
Boolits
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Boolits
S&W M&P 15-22
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
-
techguy
Re: Boolits
Rob,
I'll go in with you to buy some.. could do with some for my .300.. What weight are you planning on?
I'll go in with you to buy some.. could do with some for my .300.. What weight are you planning on?
Re: Boolits
techguy wrote:Rob,
I'll go in with you to buy some.. could do with some for my .300.. What weight are you planning on?
Shellhouse is up in Durham mate
I can buy 1000 of these http://www.shellhousebulletcompany.co.u ... ow/4199927 for £63 including postage, Simon was after 100 or so.
Also I need to talk to you about buying something from US
Rob
S&W M&P 15-22
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Boolits
Probably me :)
These for indoor sub-sonic
http://www.shellhousebulletcompany.co.u ... ow/4199900
Or these for outdoor with a gas check
http://www.shellhousebulletcompany.co.u ... ow/3485564
ShellHouse are in Lancashire, not Durham :)
DodgyRog does a nice "Soupcan" boolit which works nicely without a gas check (3.4gr N310) or a heavier round nosed "Loverin" boolit with a gas check.
These for indoor sub-sonic
http://www.shellhousebulletcompany.co.u ... ow/4199900
Or these for outdoor with a gas check
http://www.shellhousebulletcompany.co.u ... ow/3485564
ShellHouse are in Lancashire, not Durham :)
DodgyRog does a nice "Soupcan" boolit which works nicely without a gas check (3.4gr N310) or a heavier round nosed "Loverin" boolit with a gas check.
There's room for all Gods creatures, next to the mash and gravy :)
-
dromia
- Site Admin
- Posts: 20226
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Boolits
I thought Shellhouse was down Manchester way.
Shame they don't make bullets/boolits.
Shame they don't make bullets/boolits.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: Boolits
The landline is Rochdale
S&W M&P 15-22
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Boolits
To be exact they're in Bacup :)
There's room for all Gods creatures, next to the mash and gravy :)
Re: Boolits
Bloody ell :) to far to drive wherever they are
S&W M&P 15-22
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
Stoeger Sec 1
Adler a110 Sec 1
Winchester 94 .357,
Marlin 45-70
Savage 10 FP-SR .223
AI AE .308
.357 Westlake Alpha
Have slots open for.....
.22 LB pistol
.22LR rifle
-
TRX
Re: Boolits
People kept talking about how easy it was to cast bullets. I bought a couple of Lee molds for calibers I shoot, a bottom-pour pot, and scrounged a bucket of wheel weights.
I found that the temperature of the mold blocks was critical, and if I didn't strike the sprue and dump the bullet at the exact proper moment the bullet would stick in the mold. The temperature of the lead was also an issue; apparently my pot's regulator operates within generous limits.
After several HUNDRED pours, I had maybe three useable bullets.
Mostly, I think this shows one reason I don't walk and chew gum at the same time... there's a definite knack to the process.
I found that the temperature of the mold blocks was critical, and if I didn't strike the sprue and dump the bullet at the exact proper moment the bullet would stick in the mold. The temperature of the lead was also an issue; apparently my pot's regulator operates within generous limits.
After several HUNDRED pours, I had maybe three useable bullets.
Mostly, I think this shows one reason I don't walk and chew gum at the same time... there's a definite knack to the process.
Who is online
Users browsing this forum: Bing [Bot] and 5 guests