Adam question for you.
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Adam question for you.
Will the 311291 mould in .316 work in the AIA 7.62x39. My concern is that it may have feeding problems due to the boolit nose shape. What do you reckon.
-
dromia
- Site Admin
- Posts: 20226
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Adam question for you.
Don't know is the answer as I don't know how your rifle feeds.
It is an old design that was meant for bolt guns like the 03 Springfield and I have never had feeding problems with such tangent ogive designs.
I'd get a boolit with a similar nose (311284/311331/312290 not exact nose profiles but close enough) and make up some dummy rounds to the same oal as you'd use with the 311291 and see how they feed.
Why do you think it might be a problem?
It is an old design that was meant for bolt guns like the 03 Springfield and I have never had feeding problems with such tangent ogive designs.
I'd get a boolit with a similar nose (311284/311331/312290 not exact nose profiles but close enough) and make up some dummy rounds to the same oal as you'd use with the 311291 and see how they feed.
Why do you think it might be a problem?
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: Adam question for you.
The original jacketed bullet is a short bullet with a pointed nose every now and again they miss feed. Its the same with cast boolits. The rifle has a feed ramp leading into the chamber the bullet can catch on the lip of the ramp and miss feed. This is one of the reasons soup cans don't work I have to single load them. I am just wondering if the round nose might be a problem. But my question was more about chamber fit I was wondering if the .316 would work better because of the results of the chamber cast.
I think I have sourced a quantity of .316 311291 so I am going to give them a try.
I think I have sourced a quantity of .316 311291 so I am going to give them a try.
-
dromia
- Site Admin
- Posts: 20226
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Adam question for you.
As I have said before you must remember that the original bullet was designed to feed through automatic firearms not bolt guns.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Who is online
Users browsing this forum: No registered users and 8 guests