Cast loads couple questions.
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Cast loads couple questions.
If the spuds are made to fit the Lee expander die body, as previously stated, then they should be even easier to make as they won't need threading.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Cast loads couple questions.
I suspect, although I haven't had it done, that the Lyman Multi-Expand powder through die bodies or the Lee powder through expander die would serve as well for easier to machine spuds.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: Cast loads couple questions.
I have a lee universal expander some were I will dig it out and have a look.
-
meles meles
- Posts: 6335
- Joined: Mon Jun 06, 2011 8:17 pm
- Home club or Range: HBSA
- Location: Underground
- Contact:
Re: Cast loads couple questions.
Typical: science spends millions of pounds building the large Hard-on Collider and it turns out Alpha already has a universe expander in his shed..
Badger
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Cast loads couple questions.
In Middlesbrough "the land of the mutant" anything is possible.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
Demonic69
Re: Cast loads couple questions.
Anyone got a photo of these spuds? I have a lathe and may be able to tackle them.
What material are they usually made of?
What material are they usually made of?
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Cast loads couple questions.
Have you seen the previous posts.
Steel of some form just needs to be harder than brass.
Do you have a Lee neck expander die, if so then the spuds would be the same only the tapered flared point would be replaced with a suitably specified spud as per the drawings posted previously.
Steel of some form just needs to be harder than brass.
Do you have a Lee neck expander die, if so then the spuds would be the same only the tapered flared point would be replaced with a suitably specified spud as per the drawings posted previously.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
Demonic69
Re: Cast loads couple questions.
I've seen the pics yeah.
I don't have the expander die but might be able to get hold of one.
What's a reasonable price for the spuds?
I'll need to do some testing, not sure on the tolerances of the lathe at the minute as it's just getting set up.
I don't have the expander die but might be able to get hold of one.
What's a reasonable price for the spuds?
I'll need to do some testing, not sure on the tolerances of the lathe at the minute as it's just getting set up.
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Cast loads couple questions.
You have a PM.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: Cast loads couple questions.
This is what one looks like made to fit the Lee expander die. You could make it out of mild steel
- Attachments
-
- expander plug.jpg (19.9 KiB) Viewed 611 times
Who is online
Users browsing this forum: No registered users and 2 guests