Tried to but the chronograph did not like them, it is very old and does not like overcast days.dromia wrote:BTW have you chronographed those loads?
New Lapua Brass
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
Landy Dave
Re: New Lapua Brass
Re: New Lapua Brass
I am surprised that you had problems with PPU brass as I have found it to be very good indeed in fact better than one batch of Lapua cases that I had. I was told some time ago by someone who delves into these things that PPU actually source their brass from the same place as Lapua do to manufacture their cases but I cannot confirm that.
It sounds to me that you haven't quite got your reloading right yet and that there was actually nothing wrong with the PPU cases.
It sounds to me that you haven't quite got your reloading right yet and that there was actually nothing wrong with the PPU cases.
Re: New Lapua Brass
I know it is far from scientific however Lapua brass does not feel the same as PPV, Federal also has a slightly different feel to it.
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: New Lapua Brass
I'd be very interested in the velocity, you are only 2/10ths of a grain short of maximum with that load.
What load did you work up from and were the cases sticking at the start load?
What load did you work up from and were the cases sticking at the start load?
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
Yorric
Re: New Lapua Brass
Also are you getting pressure signs? 223 is not traditionally hard on cases & can usually be reloaded plenty of times. How did the PPU cases fail?
It would also be a good idea to check headspace lengths of ammo & rifle as you seem to be overworking the brass somehow.
I rarely neck size - usually full length and recently have started to anneal brass after a couple of firings to extend case life & improve neck tension control.
My 308 brass started to crack after quite a few reloads & that prompted me to get into annealing (me being tight fisted & not liking to spend cash).
If you have a neck sizer you will work the brass less. You should only need to neck size, trim & chamfer new cases.
Don't expect expensive brass to last longer than the cheaper PPU it may or may not - all brass work hardens on firing / resizing - your problems are probably down to work hardening rather than brass manufacturer.
I'm currently annealing & full length resizing all my brass as some is newer than others, some is once fired in other rifles etc. Only a couple of thousand to do so am looking at making an automatic annealer to speed it up.
It would also be a good idea to check headspace lengths of ammo & rifle as you seem to be overworking the brass somehow.
I rarely neck size - usually full length and recently have started to anneal brass after a couple of firings to extend case life & improve neck tension control.
My 308 brass started to crack after quite a few reloads & that prompted me to get into annealing (me being tight fisted & not liking to spend cash).
If you have a neck sizer you will work the brass less. You should only need to neck size, trim & chamfer new cases.
Don't expect expensive brass to last longer than the cheaper PPU it may or may not - all brass work hardens on firing / resizing - your problems are probably down to work hardening rather than brass manufacturer.
I'm currently annealing & full length resizing all my brass as some is newer than others, some is once fired in other rifles etc. Only a couple of thousand to do so am looking at making an automatic annealer to speed it up.
-
Landy Dave
Re: New Lapua Brass
I finally got the loads over a chrono and they a a wee bit quick at 3440fps.
So I will work the load up again working up from 22.4 to 24.0 at 0.2 grn intervals as that should keep me under 3280 fps.
So I will work the load up again working up from 22.4 to 24.0 at 0.2 grn intervals as that should keep me under 3280 fps.
Who is online
Users browsing this forum: No registered users and 8 guests