I hadn't considered lead cast bullets. I found these SFAB 1980/90's 'Gun Legend' cast 9mm in my storage cabinet - I'll load up a few and see how they go.
Loading 9mm
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Re: Loading 9mm
Re: Loading 9mm
Very true.Blackstuff wrote: ↑Mon Oct 16, 2023 7:11 am Just getting the bullets is the problem i've found, and to that end i've bought a Lee mould to make my own but i've not fired it up yet
Re: Loading 9mm
Hi Jersey,
Flecktarn is who I purchased my last order of 9mm FMJ from…. and they have yet to respond to an email that I sent last week re future availability of the 124. You could always try Firing Solutions to see what they have in stock?
A number of guns that I reload for are not ideally rifled for cast, hence the FMJ route.
Best wishes,
BooBoo
Flecktarn is who I purchased my last order of 9mm FMJ from…. and they have yet to respond to an email that I sent last week re future availability of the 124. You could always try Firing Solutions to see what they have in stock?
A number of guns that I reload for are not ideally rifled for cast, hence the FMJ route.
Best wishes,
BooBoo
Re: Loading 9mm
Similar here - still awaiting replies from two suppliers from last week.
Flecktarm maybe my fall back with their copper plated variety if I cannot locate some reasonable priced FMJ RN in either .45 or 9mm from any source.
What type of guns do you load for if I may ask?
Flecktarm maybe my fall back with their copper plated variety if I cannot locate some reasonable priced FMJ RN in either .45 or 9mm from any source.
What type of guns do you load for if I may ask?
Re: Loading 9mm
I'm not... Certainly pre ban days I shot a lot of cast (and still do in all of my 38's). I tried cast in both of my Glocks in times of old and my 24C loved it, far more so than my 9 equivalent. My 44 is also on cast.
Now, I have a fair collection of Heritage... and I will be trying cast again as I wish to be as gentle as possible with the older guns. 38S&W is alreadt cast, as is 455. For the SGC I'm sticking with factory for the mo. Other more modern pistols are running FMJ at present.
Now, I have a fair collection of Heritage... and I will be trying cast again as I wish to be as gentle as possible with the older guns. 38S&W is alreadt cast, as is 455. For the SGC I'm sticking with factory for the mo. Other more modern pistols are running FMJ at present.
Re: Loading 9mm
It's a good question.
I think my recent experience with my Flat & Hollow Point reloading causing misfeeds by switching between different firearms has led me to believe by choosing a particular round nose shape would benefit in two ways:
The RN closely resembles factory production & should be easier to load for correct COAL etc..,
Secondly, I've a few hundred FMJ RN already in both 115 & 124gns & I'll maintain some consistency with the power (Bullseye) & Lee (Progressive) die settings held.
It seems to be very difficult to find a source of FMJ in either weight (115 or 124gns) or the calibre of 9mm or .45 (230gn) for me to return fully to reloading.
Perhaps, when I have permission to respond to the PM's I received or may place a wanted ad I'll be able to locate some.
Regarding reloading v factory ammunition purchase:
Pricing yesterday from a local RFD has American Eagle & Magtech ammunition of 9mm @ 40p & 45acp @ 44p respectively.
Currently with the free brass & power, primers & projectiles I hold from over 10 years ago, the reload remains viable but I will run out of projectiles shortly.
With some of the prices I'm now seeing for components and difficulty in supply experienced, factory purchase may become my Hobson's choice.
There is a certain satisfaction to reloading from the manufacture to the shooting that I may become sadly precluded from.
Re: Loading 9mm
I still intend to experiment with the SFAB cast lead I posted earlier.
Re: Loading 9mm
I am currently making 124 FMJ for around 14p a bang (with components held for years). Even buying now, it would be less than 20p per round. S&B used to be reasonable but the cheapest that PPU now appears to go for is £42 a hundred.
I’ll keep making… as I enjoy shooting well with something made by me (which I also enjoy making). This has been so for over 30 years across rifle, pistol and shotgun.
If I moved over to cast then it would be 13 or so p at current prices.
I’ll keep making… as I enjoy shooting well with something made by me (which I also enjoy making). This has been so for over 30 years across rifle, pistol and shotgun.
If I moved over to cast then it would be 13 or so p at current prices.
Who is online
Users browsing this forum: No registered users and 11 guests