Cleaning Brass

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Message
Author
User avatar
Alpha1
Site Supporter Since 2020
Posts: 8553
Joined: Fri Nov 12, 2010 8:27 pm
Contact:

Cleaning Brass

#1 Post by Alpha1 »

Hi what is your preferred method of cleaning your Brass. I have all ways used a vibratory cleaner with media.
I have just acquired a rotary tumbler thingy that uses I assume a liquid with some sort of cleaning fluid and stainless pins.
How do these things work and what do you use to clean the brass and were do you buy the cleaning fluid the pins etc.
shoppe
Posts: 174
Joined: Wed Jan 25, 2017 4:57 pm
Home club or Range: Any field
Contact:

Re: Cleaning Brass

#2 Post by shoppe »

Deprime the cases . put cases into the drum. A squirt of washing up liquid. Add a good lot of water. Start machine.
That's it.
When done ,after a few hours or whatever you decide is clean enough. Empty the drum into a seive and rinse the cases making sure ALL the pins are out of the cases. I flush the cases under a running tap via both ends of the case.
Dry off in the oven with a temperature of about 60 for about 10 minutes. This bit is optional but is does make a good job.
They will air dry but takes much longer and leaves water marks.
The flushing of the cases is the worst part.
The bit of pain is making sure ALL the pins are removed from inside the cases.
Some people add various things to the water mix but I have never found the necessary.
When in operation the tumbler is a bit noisy.
Keithkilvo1
Posts: 261
Joined: Thu Sep 21, 2017 11:36 am
Home club or Range: ARPC
Contact:

Re: Cleaning Brass

#3 Post by Keithkilvo1 »

+1 for above post the only thing I do extra is put them in a towel and roll them before putting in oven, you don’t need to add anything other than washing up liquid to the water…..
User avatar
Pete
Past Supporter
Posts: 2947
Joined: Tue Sep 15, 2015 8:48 am
Home club or Range: NRA Bisley
Contact:

Re: Cleaning Brass

#4 Post by Pete »

If you want them looking like new, add a teaspoon of citric acid to the above and do a final rinse with rainwater.......that won't leave any drying marks.
I got my pins from Spud on here.

Pete
"Tantum religio potuit suadere malorum" Lucretius
You're offended? Please explain why your inability to control your emotions translates into me having to censor my opinions....
User avatar
bradaz11
Sporadic Site Supporter
Posts: 4714
Joined: Mon Jun 02, 2014 1:23 am
Home club or Range: The tunnel at Charmouth, BWSS
Location: Bristol
Contact:

Re: Cleaning Brass

#5 Post by bradaz11 »

chuck in deprimed brass and pins. fill almost to the top with water (i use hot out the tap, not out the kettle). squirt of washing up liquid, pinch of citric acid (i'll send you some with the tumbler so you can see with and without and decide if it's worth it or not) put lid on the drum, stick on base and turn on. I adjust speed for how much brass is in the drum. If you go too fast the cases are held to the wall and don't really move, too slow and they don't clean. basically turn it up until it goes quiet, then step down one. and leave it to run. when the timer runs out, look at the brass and decide if you want another go or if it's good to go. if water isn't bubbly at the end, you may need more fairy next time.

when done, empty drum into the separator. close it up and give it a few very gentle spins to clear the bulk of the pins, then go a bit faster and for a minute or so, then all the pins should be out.

depending on how soapy the brass is, I may rinse it now, or sometimes I just empty it in a bowl of water and then pull it back out to dry. some say this defeats the object of the acid, but nothing stopping you putting it in the dunk bowl too.

pull out the brass and dry. I use a food dehydrator sold for drying brass. some people throw them in the oven after dinner, some just leave them on a towel and drip dry.

then pour the dirty water out through a sieve(test first, some plastic mesh ones will let the pins through) or an old tea towel to get the pins out the bucket, chuck back in the drum to store. the pins are stainless and I've never seen any corrosion on them so you don't need to worry about them being damp. they are also magnetic, so you can pick up any dropped ones quick with a magnet tool
I use something like this, but not really sure on the search term, pretty sure I paid half that.
https://www.zoro.co.uk/shop/hand-tools/ ... ZT1002225X
When guns are outlawed, only Outlaws will have guns
User avatar
dodgyrog
Site Supporter Since 2015
Posts: 4096
Joined: Wed Jan 05, 2011 11:17 pm
Home club or Range: Three Counties Sporting Club & Gardners Guns
Location: Consett, County Durham
Contact:

Re: Cleaning Brass

#6 Post by dodgyrog »

It's simple.
I drive over to Phaedra and he puts the cases and whatever is needed into his rotary tumbler and we then go and have a chat and a cup of tea.
After about an hour the cases are ready to be decanted and dried.
I do the drying at home in my oven at 50 degrees.
A very nice arrangement that costs me a steak bake and Yum Yum from Greggs now and then.
Have a nice day.
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
Airbrush
Posts: 1246
Joined: Wed Feb 11, 2015 8:26 am
Home club or Range: Nra
Location: Devon
Contact:

Re: Cleaning Brass

#7 Post by Airbrush »

signfunnypost
User avatar
Mauserbill
Posts: 1026
Joined: Thu Jun 22, 2017 4:49 pm
Home club or Range: Range
Contact:

Re: Cleaning Brass

#8 Post by Mauserbill »

Hello
Seems like a bit of a faff, think I will stick to my vibratory cleaner with media, works well for me
User avatar
Sim G
Past Supporter
Posts: 10726
Joined: Sat Nov 06, 2010 9:09 pm
Contact:

Re: Cleaning Brass

#9 Post by Sim G »

dodgyrog wrote: Thu Jun 02, 2022 8:43 am It's simple.
I drive over to Phaedra and he puts the cases and whatever is needed into his rotary tumbler and we then go and have a chat and a cup of tea.
After about an hour the cases are ready to be decanted and dried.
I do the drying at home in my oven at 50 degrees.
A very nice arrangement that costs me a steak bake and Yum Yum from Greggs now and then.
Have a nice day.

Steak bake and a yum-yum! Brilliant. lol lol
In 1978 I was told by my grand dad that the secret to rifle accuracy is, a quality bullet, fired down a quality barrel..... How has that changed?

Guns dont kill people. Dads with pretty Daughters do...!
User avatar
Sim G
Past Supporter
Posts: 10726
Joined: Sat Nov 06, 2010 9:09 pm
Contact:

Re: Cleaning Brass

#10 Post by Sim G »

Personally, I’d never introduce a liquid to cartridge cases again! Well before kids when I had money and time, I just used to chuck pistol cases in a pillow case, then give them a “whites wash” in the machine. Couple of days later in the airing cupboard and ready to reload.

Loaded 1000 9mm and drove to Dorset for a pistol comp. First round phutt. Clumps of powder, bullet in the leade. Second round, the same…

Later I actually bent a kinetics hammer, sat on the garage floor, smoking Benson & Hedges whilst pulling the 998 remaining rounds.

Been a tumbler and walnut media man ever since!!
In 1978 I was told by my grand dad that the secret to rifle accuracy is, a quality bullet, fired down a quality barrel..... How has that changed?

Guns dont kill people. Dads with pretty Daughters do...!
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests