Would I be able to get two knives out of this old file?
It's made in Sheffield, but is there a way to know if the grade of steel is adequate for repurposing into a knife/knives?
Knife making
Moderator: dromia
Forum rules
"The Dromia Rule"
Deer Stalking… reliable word of mouth recommendation from someone you know has undertaken such stalking being offered by a specific syndicate is best. Like other walks of life, stalking has its scammers. E.G., make sure there is deer, of the species sought, on the land being made available; that appropriate insurance is in place; that there is recourse for recompense if it all goes wrong. In addition, obtain and understand terms and conditions; consider the implications of allowing a syndicate leader to be a FAC mentor; make sure ‘coaches’ are suitably qualified; consider the quality of deer management, the construction & execution of a shooting plan and safety; determine if the land is over-shot.
If in doubt, contact BASC or similar.
http://www.basc.org.uk/
Anyone considered to be a scammer will be banned without warning.
"The Dromia Rule"
Deer Stalking… reliable word of mouth recommendation from someone you know has undertaken such stalking being offered by a specific syndicate is best. Like other walks of life, stalking has its scammers. E.G., make sure there is deer, of the species sought, on the land being made available; that appropriate insurance is in place; that there is recourse for recompense if it all goes wrong. In addition, obtain and understand terms and conditions; consider the implications of allowing a syndicate leader to be a FAC mentor; make sure ‘coaches’ are suitably qualified; consider the quality of deer management, the construction & execution of a shooting plan and safety; determine if the land is over-shot.
If in doubt, contact BASC or similar.
http://www.basc.org.uk/
Anyone considered to be a scammer will be banned without warning.
- snayperskaya
- Posts: 7234
- Joined: Fri Oct 04, 2013 6:43 pm
- Home club or Range: West Bank of the Volga.....
- Location: West of The Urals
- Contact:
Re: Knife making
If you put "making a knife out of old file" into Google it's amazing how much comes up so I'd say the steel is up to it.
"The only real power comes out of a long rifle." - Joseph Stalin
Give a man a gun and he can rob a bank.....give a man a bank and he can rob the world!.
More than a vested interest in 7.62x54r!
Give a man a gun and he can rob a bank.....give a man a bank and he can rob the world!.
More than a vested interest in 7.62x54r!
- Pippin89
- Posts: 1011
- Joined: Thu Apr 04, 2019 11:54 am
- Home club or Range: Chichester Rifle and Pistol Club
- Location: West Sussex, UK
- Contact:
Re: Knife making
I make knifes as a side line hobby and sometimes a bit of a business. Files are usually pretty good. I have made a couple from used Farrier Rasps. Whether you can make 2 from a single file is really up to what knifes you are making and whether you are forging or stock removing. Obviously there is far less waste with forging but its easier to lay out and plan the use of material with stock removal. If you want to do stock removal you also have the option of whether you want to anneal it, make it and then re-heat treat it. Or you could keep it cool while making it and keep the heat treatment that it already has. I would not suggest the later. Removing hardened material is not fun in the slightest. But if you don't have the facilities to heat treat and just want to make a one off then it could be a way to do it....
Re: Knife making
I made a couple out of files! Good fun but pretty useless, couldn’t get a decent edge and it wouldn’t hold either. A forge would have helped.
- kennyc
- Posts: 2340
- Joined: Wed Jul 20, 2011 11:21 pm
- Home club or Range: hunters NRPC
- Location: Reading West Berks
- Contact:
Re: Knife making
Unless you were using completely the wrong material you weren't getting the heat treat right, I have made a few and never had a problem with edge or retention even on a 5mm thick Damascus blade, although I did have to fire up the BBQ with charcoal and use a hairdryer to get the blade hot enough to treatLampuki wrote:I made a couple out of files! Good fun but pretty useless, couldn’t get a decent edge and it wouldn’t hold either. A forge would have helped.
Re: Knife making
As above, heat treatment is king. Ideally, you need a HT oven and they are actually quite easy to make, I have a feeling I have written on here a bit about the one I made. Knife making was always at the back of my mind when we installed the surface grinder a while ago :)
Re: Knife making
It will be the heat treat without a doubt!kennyc wrote:Unless you were using completely the wrong material you weren't getting the heat treat right, I have made a few and never had a problem with edge or retention even on a 5mm thick Damascus blade, although I did have to fire up the BBQ with charcoal and use a hairdryer to get the blade hot enough to treatLampuki wrote:I made a couple out of files! Good fun but pretty useless, couldn’t get a decent edge and it wouldn’t hold either. A forge would have helped.
Cheers
Who is online
Users browsing this forum: No registered users and 1 guest