How do i go about getting custom dies made?
If I have the chamber reamer that made the barrel can I use it to ream die blanks?
Who does this?
Custom Dies
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
wildrover77
- Posts: 268
- Joined: Fri Nov 19, 2010 4:04 pm
- Location: Scarborough
- Contact:
-
meles meles
- Posts: 6335
- Joined: Mon Jun 06, 2011 8:17 pm
- Home club or Range: HBSA
- Location: Underground
- Contact:
Re: Custom Dies
wildrover77 wrote: custom dies
*Doffs cap*
Badger
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
-
essexboy
Re: Custom Dies
How do i go about getting custom dies made?
You need to get a die blank ( newlon etc) and a reamer cut for the job, not the reamer used to cut your chamber.
If you already have fired cases it would be easier to send them to Neil jones or the like to make you a set of dies.
Out of interest, what calibre?
Essexboy
You need to get a die blank ( newlon etc) and a reamer cut for the job, not the reamer used to cut your chamber.
If you already have fired cases it would be easier to send them to Neil jones or the like to make you a set of dies.
Out of interest, what calibre?
Essexboy
-
wildrover77
- Posts: 268
- Joined: Fri Nov 19, 2010 4:04 pm
- Location: Scarborough
- Contact:
Re: Custom Dies
It is .338 whisper. Ican probably get hold of some fired cases, I am in yorkshire
Re: Custom Dies
Dave Kiff of PTG (Pacific Tool and Gauge) also supplies Die Blanks as well as reamers to your own drawing or sample case.
-
essexboy
Re: Custom Dies
Nice round, have you gone for the one based on the 221 fireball or the br case version?
Hornady custom will do you a die, ssk will hold them I would think as they developed the whole whisper line. If you have a look on line there are others who have the dies off the shelf.
Good luck, I'm thinking of doing a 300 whisper myself, I few reports on how your getting on would be nice.
Essexboy
Hornady custom will do you a die, ssk will hold them I would think as they developed the whole whisper line. If you have a look on line there are others who have the dies off the shelf.
Good luck, I'm thinking of doing a 300 whisper myself, I few reports on how your getting on would be nice.
Essexboy
-
wildrover77
- Posts: 268
- Joined: Fri Nov 19, 2010 4:04 pm
- Location: Scarborough
- Contact:
Re: Custom Dies
I have been searching for hours online, Who has them on the shelf? It is the 7mmBR version. Found lots of .300 Whisper but no .338.essexboy wrote:Nice round, have you gone for the one based on the 221 fireball or the br case version?
Hornady custom will do you a die, ssk will hold them I would think as they developed the whole whisper line. If you have a look on line there are others who have the dies off the shelf.
Good luck, I'm thinking of doing a 300 whisper myself, I few reports on how your getting on would be nice.
Essexboy
SSK told me to p*** off, they only sell dies with a barrel.
Apparently Steve Bowers can make a set but cant get any reply from him.
Why can you not use the same reamers to make a die as chamber a barrel? I take it the diels need to be slightly undersize?
-
essexboy
Re: Custom Dies
A company called CH4D sell the dies and they should export them to you ok. They may have them listed under a different name, email them for the info.
Regards
Essexboy
Regards
Essexboy
Who is online
Users browsing this forum: No registered users and 6 guests