You better watch out some ooman doesn't find you in their shed!
What calibres are you thinking of regarding Ramshot? I've had good results using Tac in 223 and 308, and big game in 303 and 8mm Mauser. I get better results with reload Swiss powders. I can get either powder locally for roughly the same price.
Loading bench layout
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
WelshShooter
- Full-Bore UK Supporter
- Posts: 1812
- Joined: Wed Jun 25, 2014 9:45 pm
- Contact:
-
meles meles
- Posts: 6335
- Joined: Mon Jun 06, 2011 8:17 pm
- Home club or Range: HBSA
- Location: Underground
- Contact:
Re: Loading bench layout
We'll be looking at:
7mm Rem Mag
.243 Win
.308 Win
6.5 (x55 Swe)
9.3x74R
7.5 (x55 Swiss)
7.5 (x54 French)
7.92 Mauser
.303
and then in pistol calibres:
.45 ACP
9mm
7mm Rem Mag
.243 Win
.308 Win
6.5 (x55 Swe)
9.3x74R
7.5 (x55 Swiss)
7.5 (x54 French)
7.92 Mauser
.303
and then in pistol calibres:
.45 ACP
9mm
Badger
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
CEO (Chief Excavatin' Officer)
Badger Korporashun
Quidquid latine dictum sit altum viditur.
"Quelle style, so British"
-
WelshShooter
- Full-Bore UK Supporter
- Posts: 1812
- Joined: Wed Jun 25, 2014 9:45 pm
- Contact:
Re: Loading bench layout
In that case, the .303 and 7.92 will be well suited to Ramshot Big Game. Tac wasn't very suitable as the case necks wouldn't fully obturate until they were towards the max load, but then the cases were too tight and required full length sizing as opposed to neck sizing. The .303 shoots quite nicely with a mid range load but the Mauser does top out near max load with the Big Game powder using a 200gr SMK. My sweet spot was around 48.0gr (max load for 200gr Nosler A-bond being 50.0gr) which knocked down Fig11 targets at 900m with the sights also set to 900m but the cases do require a bit of bumping back after these loads.
Ramshot Tac is well suited to .308 but I've only tested this for 155gr bullets.
In general, the Ramshot powders meter really well using volumetric measuring devices (e.g. RCBS uniflow) to the point where I could throw 50 charges and get a range of 0.1gr. I don't have experience running it through a Lyman Gen6 but the consensus I hear about the RCBS chargemaster is that ball powder can find it's way through small gaps in the unit while dispensing powder. Something you might want to consider checking first. You won't have any issues with Vihtavuori stick powder, just remember to screw that plastic re-stricter onto the dispenser nozzle as this will obstruct the powder flow slightly which is essential during the "trickle" step of the "throw."
Ramshot Tac is well suited to .308 but I've only tested this for 155gr bullets.
In general, the Ramshot powders meter really well using volumetric measuring devices (e.g. RCBS uniflow) to the point where I could throw 50 charges and get a range of 0.1gr. I don't have experience running it through a Lyman Gen6 but the consensus I hear about the RCBS chargemaster is that ball powder can find it's way through small gaps in the unit while dispensing powder. Something you might want to consider checking first. You won't have any issues with Vihtavuori stick powder, just remember to screw that plastic re-stricter onto the dispenser nozzle as this will obstruct the powder flow slightly which is essential during the "trickle" step of the "throw."
-
bradaz11
- Full-Bore UK Supporter
- Posts: 4788
- Joined: Mon Jun 02, 2014 1:23 am
- Home club or Range: The tunnel at Charmouth, BWSS
- Location: Bristol
- Contact:
Re: Loading bench layout
i bought some ramshot true blue for 9mm, I love it, especially in a lee pro auto disc, or their new dispenser. meters like water.
seems VERY clean burning, although one thing i noticed in my SGC was with the can on, the smoke coming back at me made my eyes water, which i've not really had with S&B factory or other powders I've tried.
seems VERY clean burning, although one thing i noticed in my SGC was with the can on, the smoke coming back at me made my eyes water, which i've not really had with S&B factory or other powders I've tried.
When guns are outlawed, only Outlaws will have guns
Who is online
Users browsing this forum: No registered users and 3 guests