Good load for my 7.62 AI

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Message
Author
User avatar
Alpha1
Posts: 8627
Joined: Fri Nov 12, 2010 8:27 pm
Contact:

Re: Good load for my 7.62 AI

#31 Post by Alpha1 »

OOPS I think. :run:
Jackmanuk

Re: Good load for my 7.62 AI

#32 Post by Jackmanuk »

iv loaded up some 155 SMK ....palma (if it makes a difference) into some hornaday match brass, fiocchi primer and 48 grains of CFE 223 , im doing 600 yards on sunday at barton road so we shall see how they perform

i did try 44 and 46 grains of the CFE 223 all the rest the same and didnt really get anything to shout about so im hoping that extra bit of grunt will sort them out


iv also got 10 grains of trail boss behind a 200 grain smk so we shall see how quiet they are
User avatar
pe4king
Posts: 1402
Joined: Sat Nov 06, 2010 9:59 pm
Home club or Range: Lydd Rifle Club.
Location: Rainham, Kent.
Contact:

Re: Good load for my 7.62 AI

#33 Post by pe4king »

The best load I found for my AW was 46gr N140 with a PPU cases, Federal 210M primers,155gr smk palma loaded to 2.870, in fact I still use this in my boys Winchester with good results but to squeeze a bit more out of it 48gr of RL15 unfortunately I never got to try that one in the AW
What is a Sapper? This versatile genius condenses the whole system of military engineering and all that is useful and practical. He is a man of all work of the Army and the public ready to do anything or go anywhere, in short, he is a Sapper.
ColinR

Re: Good load for my 7.62 AI

#34 Post by ColinR »

rox wrote:
ColinR wrote:Scenars are reported as giving poor accuracy at longer ranges.
Interesting - where is this reported?

..
Never used Scenars myself but trust what Dave has to say - second post on this thread relating to Scenars in an AI. Given this post is about what works in AI's it seems relevant to pass on.
ColinR

Re: Good load for my 7.62 AI

#35 Post by ColinR »

ovenpaa wrote:The 168 SMK and the 167/168 Scenar both worked very well at shorter distances in my AI, the latter with a modest charge of N140 being my preferred McQueen load. The 168 SMK does have an issue once pushed beyond 800 and I could never get satisfactory results with the Scenar either.

Favourite load for the AI has to be a stout charge of N140 behind the Lapua 170 Lockbase.
Dave were you using Scenars in something other than an AI when shooting with rox? This post gives the impression Scenars did not work well at long range in an AI, or am I mistaken? I am presuming it was the 168 Scenars that you had problem with and 155 Scenars were OK at 1000 yds.
User avatar
ovenpaa
Posts: 24689
Joined: Fri Nov 05, 2010 8:27 pm
Location: Årbjerg, Morsø DK
Contact:

Re: Good load for my 7.62 AI

#36 Post by ovenpaa »

Colin, I would have been shooting the 155 Scenar in my Accuracy International. My choice of of the 167 Scenar for medium distance stuff, 155 Scenar for out to 1000/1100 and 170 Lockbase is because they work for me. Equally I have shot the 155 Scenar right out to 1200 although it is a bit hit and miss at 1200.
/d

Du lytter aldrig til de ord jeg siger. Du ser mig kun for det tøj jeg har paa ...

Shed Journal
ColinR

Re: Good load for my 7.62 AI

#37 Post by ColinR »

ovenpaa wrote:Colin, I would have been shooting the 155 Scenar in my Accuracy International. My choice of of the 167 Scenar for medium distance stuff, 155 Scenar for out to 1000/1100 and 170 Lockbase is because they work for me. Equally I have shot the 155 Scenar right out to 1200 although it is a bit hit and miss at 1200.
Dave, Thanks for clearing up my confusion. Much as I would expect from my own results from 168 SMK, 155 SMK and 170 LB. Like you I tend towards the 170 LB as an all round loading, but expensive and often difficult to obtain as I guess many are still going to fulfill military requirements.
Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests