Re: It’s Glock o’clock
Posted: Thu Jan 31, 2019 8:45 pm
Could save you the hassle?
![Image](https://uploads."An application"-cdn.com/20190201/0bbfaed503fdc34e7ffaa561c465390c.jpg)
TA-DAAAAAAAAAA!
I’m off down the range with it next week, I’ll let you know how it goes!
The UK's Finest Independent Forum for Shooters and Gun Owners. Est 2010.
All people seeking membership must contact admin after registering to be validated.
https://www.full-bore.co.uk/
It’s Glock o’clock
Page 2 of 6
Re: It’s Glock o’clock
Posted: Fri Feb 01, 2019 5:41 pm
TA-DAAAAAAAAAA!
I’m off down the range with it next week, I’ll let you know how it goes!
Re: It’s Glock o’clock
Posted: Fri Feb 01, 2019 9:07 pm
Love the colour, same as my new shotgun....
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 8:51 am
very nice, I bet you cant wait
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 9:36 am
Very cool indeed. What's the weight like?
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 10:01 am
Yep I like that, what's the price like?
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 10:05 am
Base pistol with two ten rounders and a fifteen is £850 or a bit less.
That lot was £1035.
Weight is nice, balance is good I think, I’m just printing the suppressor insert. He sells them but I’m making my own.
Yes, the barrel stops just inside that can, the can is welded on and the end cap comes off.....
I’m going to play around with baffle designs, given the freedom of 3D printing, all sorts of twists and turns are possible when you don’t have to bend to the will of the lathe.
That lot was £1035.
Weight is nice, balance is good I think, I’m just printing the suppressor insert. He sells them but I’m making my own.
Yes, the barrel stops just inside that can, the can is welded on and the end cap comes off.....
I’m going to play around with baffle designs, given the freedom of 3D printing, all sorts of twists and turns are possible when you don’t have to bend to the will of the lathe.
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 10:09 am
so how do you clean the barrel? just leave the slide hanging over the barrel, or have they done something to slide so it can pass through?
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 10:56 am
Is it for plinking only?
Re: It’s Glock o’clock
Posted: Sat Feb 02, 2019 11:14 am
It’s strips like a regular Glock (the lower is Gen 3 compatible) and you can tilt the barrel to clean the breech face etc, it’s easy enough to clean but you cannot remove the barrel from the slide.
The barrel isn’t secured by anything to the frame, just like a regular pistol.
I’d be quite surprised if it turned out anywhere near as accurate as a k22 but not that surprised if it was as good as the GSG 1911.
It’s for steels and perhaps three gun type stuff, mostly it’s because Glock though, I’ve always loved them in the hand and the chance to own a legal one was far too tempting to pass up.
Range report next week with luck, depends somewhat on the snow....
The barrel isn’t secured by anything to the frame, just like a regular pistol.
I’d be quite surprised if it turned out anywhere near as accurate as a k22 but not that surprised if it was as good as the GSG 1911.
It’s for steels and perhaps three gun type stuff, mostly it’s because Glock though, I’ve always loved them in the hand and the chance to own a legal one was far too tempting to pass up.
Range report next week with luck, depends somewhat on the snow....