Sitting watching K9 with a malt whiskey in hand (and mouth) - ready to start again tomorrow! COOL.
Boolits
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Boolits
3k .357 boolits - cast, sized and lubed. Job done.
Sitting watching K9 with a malt whiskey in hand (and mouth) - ready to start again tomorrow! COOL.
Sitting watching K9 with a malt whiskey in hand (and mouth) - ready to start again tomorrow! COOL.
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
Re: Boolits
Is that Kg or 1000?
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Boolits
That'll be 1000's. I'm cream crackered - time for a top up!
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
Re: Boolits
1000's? OK, you deserve a drink :)
Do you do anything suitable for a No4 Mk1 that will work to 1000 yards and with the right load could give similar drops to MkVII Ball?
Do you do anything suitable for a No4 Mk1 that will work to 1000 yards and with the right load could give similar drops to MkVII Ball?
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Boolits
I can do a heavy 190 gr 'ish .315 boolit.
The mould is Dromia's. Nice man lets me use it.
The mould is Dromia's. Nice man lets me use it.
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
idge
Re: Boolits
hi dodgyrog just joined the forum and im interested in lookin into shootin cast boolits through my swiss k11 do you make anything that would be suitable ?
-
dromia
- Site Admin
- Posts: 20221
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Boolits
Really depends on your rifles throat measurements, the K11's are notoriously short throated so you need a good bore riding design that meets groove and bore diameters well to get the weight.
You need to slug your bore and impact cast the throat.
Then when you have those measurements for your rifle you can meaningfully ask for a suitable boolit.
You need to slug your bore and impact cast the throat.
Then when you have those measurements for your rifle you can meaningfully ask for a suitable boolit.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: Boolits
Idge, slugging is a very simple process and I have some soft lead slugs sized and ready to go, I can pop a few in the post if you want to have a go.
-
idge
Re: Boolits
well thanks dromia but i was "meaningfully" asking for a suitable boolit but seeing as i dont have any experiance in the area the advice is also what i need , i have slugged a bore before so i did my k11 today and it turned out at .308 5 dont have the ability to chamber cast though .
-
dromia
- Site Admin
- Posts: 20221
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: Boolits
Thats a start, if you can slug a bore then you can do an impact cast.
Directions are here in the Library towards the end of the article: http://www.full-bore.co.uk/viewtopic.php?f=36&t=855
Directions are here in the Library towards the end of the article: http://www.full-bore.co.uk/viewtopic.php?f=36&t=855
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Who is online
Users browsing this forum: Bing [Bot] and 7 guests