Australian International Arms

Message

#1 Post by **Dellboy** » Sun Oct 11, 2020 10:55 pm

Australian International Arms
No4 Type
Model M10-A1
Calibre 7.62x39mm

anyone experience with them some seem to say they are not that good ?

thanks in advance

#2 Post by **Sim G** » Sun Oct 11, 2020 11:05 pm

I think Alpha 1 has one. And if memory serves, he likes it. A guy in the club had one, and he didn't like his...

#3 Post by **bradaz11** » Mon Oct 12, 2020 12:07 am

That's what bloke on the range's frankenrifle is. I'd give one cabinet space

Sent from my pink toy using "An application"

#4 Post by **ovenpaa** » Mon Oct 12, 2020 7:53 am

Wood fit and quality has varied wildly on the ones we have had in.

#5 Post by **dromia** » Mon Oct 12, 2020 8:27 am

I would have one also if I could find one that shoots, accuracy fit and finish is all over the place with them. I must have had half a dozen examples through my hands over the years and none of them would group worth a damn.

There are some good shooters around as I have shot them but unfortunately for would be purchasers the owners tend to hold on to them.

I wouldn't buy one unless I was certain of its accuracy provenance, I would be at least expecting consistent 2" 100 yard benched groups with hand loaded/hand cast ammunition and bullets.

GeeRam · #6 Post by **GeeRam** » Mon Oct 12, 2020 8:38 am

dromia wrote: There are some good shooters around as I have shot them but unfortunately for would be purchasers the owners tend to hold on to them.

There was a guy a couple of firing points away from us at Bisley yesterday with one of them, when we were doing a 300yrd shoot.......so I guess he's either found out it's rubbish, or he's got a good 'un, and will not be letting go of it.

#7 Post by **Alpha1** » Mon Oct 12, 2020 9:39 am

Mine is the short carbine version. A Lee Enfield No4 is a better buy than the Australian arms No4 type. As said the fit and Finnish can be a bit ropey and they are not an accurate rifle.
Mine is a good one but I had to spend some time on load development the round is 7.62x39 the bores are normally around the .310/.311 mark. I slugged my bore and took a chamber cast I then bought a NOE Loverin bullet mould based on those results for mine and that was the turning point. I only shoot cast bullets in it. I have a load I use indoors at 25yards and I shoot it at 100 yards outdoors.
It's a fun gun I have had it a long time and its a keeper.

GeeRam · #8 Post by **GeeRam** » Mon Oct 12, 2020 9:49 am

Worth having a read of what Paul Green of Thames Valley Guns wrote of his experience with them, here....

https://www.thamesvalleyguns.co.uk/AIA_M10A1.pdf

Echoes what others have said already.

#9 Post by **Alpha1** » Mon Oct 12, 2020 10:24 am

Mine is the same model as the one in the article. I removed the flash hider from mine. My bore is .309/.310 the grooves are .313 the same as his. Mine feeds OK.

#10 Post by **Dellboy** » Mon Oct 12, 2020 11:14 am

well what started as a hunt for a vgood no 5 has become somewhat complicated

The UK's Finest Independent Forum for Shooters and Gun Owners. Est 2010.

Australian International Arms

Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Re: Australian International Arms

Who is online