Does anyone reload blanks for 12 bore ?
Mate asked me the other day if i could load some for a re enactment morter. At the moment he is buying the short shotgun mine ones AND PAYING OVER A POUND A POP .
So what do you or would you use to provide smoke and bang
pyrodex 777 toilet roll wad wax top seal ?
Thoughts
Blanks for 12 bore
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
Dellboy
- Full-Bore UK Supporter
- Posts: 2636
- Joined: Wed Aug 31, 2011 11:49 am
- Home club or Range: Star Shooting Club
- Location: Essex
- Contact:
Blanks for 12 bore
2020 GOOD DEALS WITH
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
Cutch Vortex Scope
Mauserbill Enfield Books
Enjoy today as tomorrow might not come .
Noli pati a scelestis opprimi.
002515
-
450 Martini
- Posts: 319
- Joined: Tue May 14, 2013 11:28 pm
- Home club or Range: Swadlincote RPC
- Contact:
Re: Blanks for 12 bore
Yes that should work. I usually use black powder and a card wad with water glass glue. I cut the cases short as the full case capacity is not needed.
-
Blackstuff
- Full-Bore UK Supporter
- Posts: 7847
- Joined: Sun Nov 07, 2010 1:01 pm
- Contact:
Re: Blanks for 12 bore
I would crimp close the cases so there's nothing that can be determined to be a 'projectile'
DVC
-
Mattnall
- Full-Bore UK Supporter
- Posts: 2940
- Joined: Wed Mar 06, 2013 5:32 pm
- Home club or Range: NRA, Redricks TSC, BS1944RC, HRA
- Location: East Herts
- Contact:
Re: Blanks for 12 bore
I know one re-enacter that uses fibre wad 12ga cartridges and cuts the shot off - wad is shredded by the wad-shredder in the bore that also stops full 12ga being inserted.
They should have a limiter in to stop full length cartridges being used by mistake.
They should have a limiter in to stop full length cartridges being used by mistake.
Arming the Country, one gun at a time.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
Who is online
Users browsing this forum: No registered users and 2 guests