.310 Cadet

This section is for reloading and ammunition only, all loads found in here are used strictly at your own risk, if in doubt ask again.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should treated as suspect and not used.

Moderator: dromia

Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.

Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Post Reply
Message
Author
User avatar
Alpha1
Site Supporter Since 2020
Posts: 8553
Joined: Fri Nov 12, 2010 8:27 pm
Contact:

.310 Cadet

#1 Post by Alpha1 »

What size bullet are you guys casting for the .310 Cadet?
User avatar
dromia
Site Admin
Posts: 19964
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:

Re: .310 Cadet

#2 Post by dromia »

Depends on the chamber and bore size.

My current one shoots a 0.316" body with a 0.308" heel delivering the legendary 310 Cadet accuracy.

I have had them as big as needing a 0.324" body diameter bullet.

As always bullet fit is king so take a chamber/lead/bore cast and then you will know what bullet the rifle will need rather than speculating on that which fits anything other than your gun.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit

http://www.pukkabundhooks.com/
FredB
Site Supporter Since 2019
Posts: 969
Joined: Fri Dec 10, 2010 8:33 pm
Home club or Range: stourport
Location: Wolverhampton
Contact:

Re: .310 Cadet

#3 Post by FredB »

Groove diameters of .316 are something of a legend in the 310 cadet shooting fraternity. I have never come across one, and I have slugged a lot over the years for fellow club members. Every one that I have measured has been .320. My RCBS mould casts out at .322". If you slug my rifle and then attempt to measure the diameter by rotating the slug in a vernier caliper, you get around .316".
It is eary to measure the diameter of a slug from a barrel with an odd number of grooves if you have access to a lathe. Chuck up a piece of scrap metal and drill an undersized hole in it. Then, with a boring bar, gradually open up the hole until the slug will just slide into it. Then measure the diameter of the hole.

Fred
User avatar
dromia
Site Admin
Posts: 19964
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:

Re: .310 Cadet

#4 Post by dromia »

The trick is to measure the diameter just in front of the case mouth and before the rifling starts, the freebore. No need to worry about odd groove numbers, although I use a "V" block to measure them.

Getting the bullet to just sit in the freebore keeping it centred means that you don't need to worry about the groove size although my current Cadet measures 0.316" both for freebore and groove diameters.

In all the many Cadets I have had the RCBS mould has always been too big for a good chambering, many a time this has been because of the oversize heel needing the case expanding before it will seat and this case mouth diameter being to great to chamber. Lovely mould the RCBS but I don't know why I still have mine as I haven't used it in decades.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit

http://www.pukkabundhooks.com/
User avatar
Alpha1
Site Supporter Since 2020
Posts: 8553
Joined: Fri Nov 12, 2010 8:27 pm
Contact:

Re: .310 Cadet

#5 Post by Alpha1 »

The RCBS mold is the only one I have Im afraid.
teanews hmm whats next.
User avatar
dromia
Site Admin
Posts: 19964
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:

Re: .310 Cadet

#6 Post by dromia »

A good impact cast of the freebore and rifling.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit

http://www.pukkabundhooks.com/
User avatar
Alpha1
Site Supporter Since 2020
Posts: 8553
Joined: Fri Nov 12, 2010 8:27 pm
Contact:

Re: .310 Cadet

#7 Post by Alpha1 »

dromia wrote:A good impact cast of the freebore and rifling.
Yes, that does make sense. But only having the RCBS mold Im not sure its going to help.
I don't shoot it that often. In fact the boolits I'm using of which there are very few left I got from you. They are from one of your molds.
You gave me a box full for free to try after purchasing a firearm in your establishment if I remember rightly. Many moons ago.
User avatar
dromia
Site Admin
Posts: 19964
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:

Re: .310 Cadet

#8 Post by dromia »

Accurate do my 310 cadet bullet and Tom will cut to your size both for body and heel at no extra cost.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit

http://www.pukkabundhooks.com/
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests