6.5x55/SCAN
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Re: 6.5x55/SCAN
Thanks for the information.
Re: 6.5x55/SCAN
There's a lot of confusion about the term "SCAN". It's not about chamber-pressure but dimentions. Vihtavuori made reloading data specifically for the scandinavian Sauer 200 STR shooters. This has also been included in their english written reloading manual and creates a lot of confusion.
http://gammel.landro.no/produkter/ladin ... dedata.pdf
Back in 1893, the norwegian – swedish caliber commission agreed on a common caliber and cartridge for both countrys armys. The idea was that norwegian and swedish ammo should be interchangeable. Then there’s the old story about the swedish officer, who during a trip to Norway, bought a Krag and some ammo. Back in Sweden, he also tried the ammo in his Mauser, and it wouldn’t chamber. This created a big fuzz in Sweden, and the rumour sayd that the norwegians had cheated them and made ammo that would not work in swedish rifles. The swedes even made a commite to investigate the matter. The verdict were that the norwegian chambers were close to the max. of the agreed specs., while the swedish chambers were close to the minimum. Some swedish Mausers needed a heavier push on the bolt to close with norwegian ammo, but the difference were deemed to be insignifficant.
Later, when the Sauer 200 str, was introduced as standard target rifle for the scandinavian countries, the 6,5 x 55 skan was introduced as a new attempt to standardize the ammunition. The skan chamber should be a compromise between the norwegian and the swedish chambers. I think all new target barrels from around 1990 and onwards has Skan chambers.
You can read the whole thread here: My answer in post # 32
http://forums.gunboards.com/showthread. ... n-question
http://gammel.landro.no/produkter/ladin ... dedata.pdf
Back in 1893, the norwegian – swedish caliber commission agreed on a common caliber and cartridge for both countrys armys. The idea was that norwegian and swedish ammo should be interchangeable. Then there’s the old story about the swedish officer, who during a trip to Norway, bought a Krag and some ammo. Back in Sweden, he also tried the ammo in his Mauser, and it wouldn’t chamber. This created a big fuzz in Sweden, and the rumour sayd that the norwegians had cheated them and made ammo that would not work in swedish rifles. The swedes even made a commite to investigate the matter. The verdict were that the norwegian chambers were close to the max. of the agreed specs., while the swedish chambers were close to the minimum. Some swedish Mausers needed a heavier push on the bolt to close with norwegian ammo, but the difference were deemed to be insignifficant.
Later, when the Sauer 200 str, was introduced as standard target rifle for the scandinavian countries, the 6,5 x 55 skan was introduced as a new attempt to standardize the ammunition. The skan chamber should be a compromise between the norwegian and the swedish chambers. I think all new target barrels from around 1990 and onwards has Skan chambers.
You can read the whole thread here: My answer in post # 32
http://forums.gunboards.com/showthread. ... n-question
Re: 6.5x55/SCAN
Thanks for the information.
Re: 6.5x55/SCAN
Good afternoonSim G wrote:Alpha1 wrote:The micrometer seating stem works with my .222 die. It will also work for 6.55x55. So a result the sizing die is no good to me I have never heard of any one shooting this caliber so Ill probably just bin it.
There was a Sauer 202 Wolverine in 6.5x55 Skan advertised in the for sale section of this forum for several months.......
And you were the second post on the thread!
http://full-bore.co.uk/viewtopic.php?f= ... =Wolverine
I think I am now the proud owner of this very rifle (can't imagine there are two to exactly that spec!). I've been doing some searching about the differences (if any) between "plain" 6.5 x 55 and 6.5 x 55 SKAN and I'm still confused. What is the current opinion on whether there are any meaningful differences between the two? The rifle shoots extremely well as expected, but I want to make sure I'm first not doing anything potentially hazardous and second whether I'm getting the best out of it.
I have a set of RCBS dies described on the box as "6.5MMX55 SWED MAU"; I have both a full-length and neck sizing die. Are these suitable for, or indeed best for, this calibre?
Thanks in advance
Andrew
- dromia
- Site Admin
- Posts: 20229
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: 6.5x55/SCAN
Have you read Lauries post on this thread, he covers your questions.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Re: 6.5x55/SCAN
Thanks, I've had another read of that post - seems it should be OK to use "SE" dies to reload for a SKAN-chambered rifle then?dromia wrote:Have you read Lauries post on this thread, he covers your questions.
- dromia
- Site Admin
- Posts: 20229
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: 6.5x55/SCAN
Whatever Laurie says is always worth taking heed of.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Who is online
Users browsing this forum: No registered users and 8 guests