Hi all,
Can anyone point me in the direction of a 2 or 6 cavity "Truncated" mold for 158gr .358 ?
I've got a 158gr .358 Lee RNFP but I would like to know who makes a mold for truncated cone 158gr?
Anyone?
Regards
John
Looking for a 158gr .358 Truncated Mold
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
graphictart
- Posts: 94
- Joined: Fri Jun 08, 2012 9:07 am
- Home club or Range: NRA, Bisley
- Location: Berkshire
- Contact:
-
saddler
Re: Looking for a 158gr .358 Truncated Mold
Have a double cavity 358 mold. Ideal #358429
It's one of the best designs...being very close to the original Elmer Keith specification...
It's one of the best designs...being very close to the original Elmer Keith specification...
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Looking for a 158gr .358 Truncated Mold
Have a look:
http://www.three-peaks.net/bullet_molds.htm
http://www.three-peaks.net/bullet_molds.htm
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
graphictart
- Posts: 94
- Joined: Fri Jun 08, 2012 9:07 am
- Home club or Range: NRA, Bisley
- Location: Berkshire
- Contact:
Re: Looking for a 158gr .358 Truncated Mold
saddler wrote:Have a double cavity 358 mold. Ideal #358429
It's one of the best designs...being very close to the original Elmer Keith specification...
Midway has it down as a semi wad cutter:
http://www.midwayusa.com/product/766375 ... -wadcutter
-
mag41uk
- Posts: 1847
- Joined: Sat Oct 13, 2012 3:50 pm
- Home club or Range: Aldershot R & P Club
- Location: Reading
- Contact:
Re: Looking for a 158gr .358 Truncated Mold
I would look for a 4 cavity saeco mould. They are most excellent but not cheap.
I would also look out for a 4 cavity Lyman mould.
Worth having a look on ebay.com.
You could get accurate moulds to make you one. Very good quality but not cheap.
MP moulds would also be very good as he is in Europe but he has sod all in stock.
He has a nice looking 140gn TC type bullet in 6 cavity for $99 and it takes Lee handles.
Tony
I would also look out for a 4 cavity Lyman mould.
Worth having a look on ebay.com.
You could get accurate moulds to make you one. Very good quality but not cheap.
MP moulds would also be very good as he is in Europe but he has sod all in stock.
He has a nice looking 140gn TC type bullet in 6 cavity for $99 and it takes Lee handles.
Tony
-
graphictart
- Posts: 94
- Joined: Fri Jun 08, 2012 9:07 am
- Home club or Range: NRA, Bisley
- Location: Berkshire
- Contact:
Re: Looking for a 158gr .358 Truncated Mold
Thanks guys,
Really got me digging into google and I think I've found what I'm looking for:
http://www.midwayuk.com/epages/Midway_U ... cts/145059
A bit pricy but thats the bullet profile I'm after. I think its the same mold as the "GM Hard cast bullets"
John
Really got me digging into google and I think I've found what I'm looking for:
http://www.midwayuk.com/epages/Midway_U ... cts/145059
A bit pricy but thats the bullet profile I'm after. I think its the same mold as the "GM Hard cast bullets"
John
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Looking for a 158gr .358 Truncated Mold
Put yourself down for this group buy - more suited to your needs but probably a long wait!
http://castboolits.gunloads.com/showthr ... F-%28RD%29
http://castboolits.gunloads.com/showthr ... F-%28RD%29
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
Who is online
Users browsing this forum: No registered users and 7 guests