OK, so I know that armoured piercing ammunition is section 5. Here's the thing, some mil surp however has a steel core (7.62R, 5.56 etc) and these rounds have been known to go through steel. My question is at what point does it actually become section 5.
Yours, confused
Charlotte
Steel cores, what section of the act?
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
Charlotte the flyer
- Posts: 1155
- Joined: Sat Oct 20, 2012 11:02 am
- Home club or Range: Classified
- Location: Staffs
- Contact:
Steel cores, what section of the act?
The above post probably contains sarcasm or some other form of attempted wit, please don't take it to heart.
-
saddler
Re: Steel cores, what section of the act?
If classed as Ball...then Section 1
If made as dedicated AP...then Section 5
The American military in WW2 issued the .30 M2 AP round as standard for battlefield use. Ball ammo was reserved for marksmanship training. The reason being that they classed the battlefield as an armored environment, so wanted everyone to have means to make holes in half-tracks, etc.
There is quite a bit of difference between ball and AP, not just a core
If made as dedicated AP...then Section 5
The American military in WW2 issued the .30 M2 AP round as standard for battlefield use. Ball ammo was reserved for marksmanship training. The reason being that they classed the battlefield as an armored environment, so wanted everyone to have means to make holes in half-tracks, etc.
There is quite a bit of difference between ball and AP, not just a core
-
tackb
Re: Steel cores, what section of the act?
What's the difference ? I sectioned a 308 ap round years ago and all I found was a core?
-
andy h
Re: Steel cores, what section of the act?
Armour piercing section 5 relates to hardened steel penetrating cores , I have sectioned a russian ak round and the piece of steel inside was just a section of a mild steel round bar bolt cropped to length and not hardened.
-
Mattnall
- Full-Bore UK Supporter
- Posts: 2939
- Joined: Wed Mar 06, 2013 5:32 pm
- Home club or Range: NRA, Redricks TSC, BS1944RC, HRA
- Location: East Herts
- Contact:
Re: Steel cores, what section of the act?
I think it comes down to what the bullet is designed to be. If designed as AP the S5, if not specifically designed as AP then S1.
Same as expanding ammo.
Same as expanding ammo.
Arming the Country, one gun at a time.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
Who is online
Users browsing this forum: No registered users and 4 guests