Hi all quite new to reloading so you will have to patient with me.
i have reloaded some factory round ppu brass and after one reload most of the cases have tiny splits around the top of the cases.
i have some Winchester brass and i have reloaded this 6 times and its fine.
the one thing i have noticed is that the factory ppu brass has some strange crimp type marks where the splits have appeared .
was going to attach photo but cant see to do it for some reason ?
please advise. wtfwtf
.44 Magnum brass splitting !
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: .44 Magnum brass splitting !
Suggest that you anneal the brass.
Was the brass, both Winchester and PPU, bought second hand/new or fired factory by yourself?
Was the brass, both Winchester and PPU, bought second hand/new or fired factory by yourself?
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
ninja_geezer
Re: .44 Magnum brass splitting !
all brass was new , the Winchester was in bags of 100 and the PPU was factory rounds.dromia wrote:Suggest that you anneal the brass.
Was the brass, both Winchester and PPU, bought second hand/new or fired factory by yourself?
how do i post a picture ?
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: .44 Magnum brass splitting !
See here for attaching images:
http://www.full-bore.co.uk/viewtopic.php?f=17&t=10130
If the brass is from new then you would be best placed to know the cause of any crimp marks.
Is all the brass trimmed to the same length?
http://www.full-bore.co.uk/viewtopic.php?f=17&t=10130
If the brass is from new then you would be best placed to know the cause of any crimp marks.
Is all the brass trimmed to the same length?
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
dromia
- Site Admin
- Posts: 20225
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: .44 Magnum brass splitting !
Looks like a very hard crimp guaranteed to work harden brass unless annealed.
Is it a Lee factory crimp die you are using?
If so it is a brutal tool and should be used sparingly.
What about case length?
Any reason why you don't shoot cast boolits?
They take a gentler roll crimp.
Is it a Lee factory crimp die you are using?
If so it is a brutal tool and should be used sparingly.
What about case length?
Any reason why you don't shoot cast boolits?
They take a gentler roll crimp.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
ninja_geezer
Re: .44 Magnum brass splitting !
sorry i did not crimp that round it is a factory crimp ppu round.dromia wrote:Looks like a very hard crimp guaranteed to work harden brass unless annealed.
Is it a Lee factory crimp die you are using?
If so it is a brutal tool and should be used sparingly.
What about case length?
Any reason why you don't shoot cast boolits?
They take a gentler roll crimp.
the case on the left is the result after the first reload of the factory round.
-
ninja_geezer
Re: .44 Magnum brass splitting !
the case on the left is a twice fired factory ppu .spot the difference !
-
Mike357
- Posts: 3637
- Joined: Sat Dec 04, 2010 7:25 pm
- Home club or Range: NRA, Bisley, Dundee Rifle & Pistol Club & Bishop Auckland GC
- Location: Near Durham(ish)!
- Contact:
Re: .44 Magnum brass splitting !
Damn! I have cases split on me all the time now but that is because my brass has been reloaded an unknown number of times as it was secondhand when I got it.
As Dromia says, use a very light crimp. As long as it holds the boolit in place in a tube magazine and can stand the pressure during loading then that's really all you need.
What powder charge are you using?
As Dromia says, use a very light crimp. As long as it holds the boolit in place in a tube magazine and can stand the pressure during loading then that's really all you need.
What powder charge are you using?
It's not the pace of life that concerns me, it's the sudden stop at the end!
-
ninja_geezer
Re: .44 Magnum brass splitting !
i think my crimp is light, the powder charge at the moment is 9.2 grains of unique 240 cast bulletMike357 wrote:Damn! I have cases split on me all the time now but that is because my brass has been reloaded an unknown number of times as it was secondhand when I got it.
As Dromia says, use a very light crimp. As long as it holds the boolit in place in a tube magazine and can stand the pressure during loading then that's really all you need.
What powder charge are you using?
tried all manor of variations from 6 grains up to 11.8 and this seems the most accurate.
Who is online
Users browsing this forum: No registered users and 6 guests