Getting a shotgun barrel cut for a choke?

All things shotgun related.

Moderator: dromia

Message
Author
Rarms
Past Supporter
Posts: 432
Joined: Wed Aug 01, 2012 1:52 pm
Contact:

Getting a shotgun barrel cut for a choke?

#1 Post by Rarms »

Anyone any experience of where to get this done? Have a Remington 1100 barrel and want to get it screw cut for a choke tube....

Thanks
Triffid
Past Supporter
Posts: 407
Joined: Thu Feb 27, 2014 2:36 pm
Home club or Range: Wey Valley
Contact:

Re: Getting a shotgun barrel cut for a choke?

#2 Post by Triffid »

Rarms
Past Supporter
Posts: 432
Joined: Wed Aug 01, 2012 1:52 pm
Contact:

Re: Getting a shotgun barrel cut for a choke?

#3 Post by Rarms »

Is £150 the going rate as it were? Anyone know anyone in Sussex?
42DAF
Posts: 76
Joined: Wed Mar 13, 2019 9:33 pm

Re: Getting a shotgun barrel cut for a choke?

#4 Post by 42DAF »

You have a choice of two companies Teague chokes and Briley neither are particularly cheap and with a Remi 1100 you almost certainly be better off finding a multichoke barrel to fit onto your gun.
If you have retrofitted chokes fitted there are very few guns where you will get that money back at resale, of course if your never selling the gun it wont matter.

Why are you looking for a multichoke has to be a real consideration as a change of cartridge can have the same effect and most people can't truly tell the difference been a point of choke in real world shooting
User avatar
Blackstuff
Site Supporter Since 2015
Posts: 7709
Joined: Sun Nov 07, 2010 1:01 pm
Contact:

Re: Getting a shotgun barrel cut for a choke?

#5 Post by Blackstuff »

If you go the Teague (and presumably Briley too), you also have to factor in the cost of the propriatary chokes you must use afterwards too. £44 a pop from Teague so if you use a few it soon adds up....

As mentioned you're better off sourcing an existing multichoke barrel.
DVC
Rarms
Past Supporter
Posts: 432
Joined: Wed Aug 01, 2012 1:52 pm
Contact:

Re: Getting a shotgun barrel cut for a choke?

#6 Post by Rarms »

Looking to get it threaded to fit a moderator!
42DAF
Posts: 76
Joined: Wed Mar 13, 2019 9:33 pm

Re: Getting a shotgun barrel cut for a choke?

#7 Post by 42DAF »

Just go straight to saddlery and gunroom they do the moderator conversions mainly with out multi choke be cheaper and better.
Rarms
Past Supporter
Posts: 432
Joined: Wed Aug 01, 2012 1:52 pm
Contact:

Re: Getting a shotgun barrel cut for a choke?

#8 Post by Rarms »

This is a different type of mod. Needs to be threaded
42DAF
Posts: 76
Joined: Wed Mar 13, 2019 9:33 pm

Re: Getting a shotgun barrel cut for a choke?

#9 Post by 42DAF »

The issue is Teague and Briley are thin walls and each gun has a bespoke cut thread so you’ll need a bespoke threaded moderator.

You best bet is finding a factory Multichoke barrel if your set on that moderator choice.
Rarms
Past Supporter
Posts: 432
Joined: Wed Aug 01, 2012 1:52 pm
Contact:

Re: Getting a shotgun barrel cut for a choke?

#10 Post by Rarms »

I think I am set on this mod. I have a couple of hush power pumps and want to try a semi. The barrel is 24 inch so will be thicker than normal at the muzzle compared to a 28 or 30 inch
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests