Excuse my ignorance
!44 mag reloading
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
-
6.5shooter
Re: 44 mag reloading
Would copper plated bullets for higher velocities not just be simpler and less hassle?
Excuse my ignorance!
Excuse my ignorance
!-
Sandgroper
- Posts: 4735
- Joined: Sat Nov 06, 2010 3:45 pm
- Location: Stanley, Falkland Islands
- Contact:
Re: 44 mag reloading
I've use Rainier copper plated bullets to great effect in my 357 Winchester but Rainier recommends 1500fps as a maximum velocity - so you're back to square one if you want to go faster!6.5shooter wrote:Would copper plated bullets for higher velocities not just be simpler and less hassle?
Excuse my ignorance
“The standard you walk past is the standard you accept.”
Lieutenant General David Morrison
I plink, therefore I shoot.
Lieutenant General David Morrison
I plink, therefore I shoot.
-
dromia
- Site Admin
- Posts: 19991
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: 44 mag reloading
There is no hassle with cast boolits, just buy them off the shelf cast and sized to fit your gun if you don't want the fun and improved performance of casting your own.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
-
dromia
- Site Admin
- Posts: 19991
- Joined: Sat Nov 06, 2010 4:57 am
- Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
- Location: Sutherland and Co Durham
- Contact:
Re: 44 mag reloading
I forgot to mention in the previous post about Xlox is the reason why people think it is the lube is because you tumble the boolits as cast so unsized and therefore they tend to fit better so no leading. People then think it is the lube when actually it accidental boolit fit.
Come on Bambi get some
Imperial Good Metric Bad
Analogue Good Digital Bad
Fecking stones
Real farmers don't need subsidies
Cow's farts matter!
For fine firearms and requisites visit
http://www.pukkabundhooks.com/
Who is online
Users browsing this forum: No registered users and 7 guests