Martini Henry

Pre 1945 action rifles. Muzzle loading.

Moderator: dromia

Post Reply
Message
Author
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Martini Henry

#1 Post by Vossie »

Well got my very beloved MH out the cabinet for an admire as i thought i may cast up some more bullets, and found a crack in the stock.
It turned out to worse than I thought, I am gutted.

Do I attempt this myself, or find someone more experienced.

She is a BSA MKIII, and dream to own and shoot.

No replacements online at all.
Attachments
20231019_134535.jpg
FredB
Site Supporter Since 2019
Posts: 969
Joined: Fri Dec 10, 2010 8:33 pm
Home club or Range: stourport
Location: Wolverhampton
Contact:

Re: Martini Henry

#2 Post by FredB »

Why not? Epoxy resin. Fitbit together carefully after applying the resin an then tape it up tightly until securely set. It will probably be stronger than it was when new.
Fred
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Re: Martini Henry

#3 Post by Vossie »

thankssign

It is my plan, but wanted to.seek advice before I go for it.
User avatar
450 Martini
Posts: 316
Joined: Tue May 14, 2013 11:28 pm
Home club or Range: Swadlincote RPC
Contact:

Re: Martini Henry

#4 Post by 450 Martini »

It is repairable with epoxy although you may have to refinish the wood after removing excess glue. The wood looks nice and dry and not too oily and this will help the resin bond.
Most of the ex Nepal Martini rifles imported from the US now have severely damaged stocks and split wrists. I have repaired a few by splicing walnut into the splits and these have held up well in use over the last few years. Remember to take care not to let too much resin get into the bolt channel or you won't get the stock bolt in.
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Re: Martini Henry

#5 Post by Vossie »

450 Martini

Thank you, it has taken some effort to back out the stock bolt. It was in there tight.
Have cleaned up damaged area to remove most of the oil.
I have to do this old girl some justice, as it is most enjoyable rifle I have.
Martiniman
Posts: 8
Joined: Sun Jun 18, 2023 9:53 pm
Home club or Range: VAA
Contact:

Re: Martini Henry

#6 Post by Martiniman »

How did it go? May know of a MKIV forestock you could affect a repair from it?
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Re: Martini Henry

#7 Post by Vossie »

It has been repaired, be a while before I get to shoot it. I had to remove some wood and replace it.
I will try and post a picture of the final repair.
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Re: Martini Henry

#8 Post by Vossie »

Can see the replaced part, used a very hard wood, it was the only way to save it and preserve the original look from the outside.
Only if you know where the split can it be seen.
Attachments
20231105_115516.jpg
Screenshot_20231114_210710_Gallery.jpg
Martiniman
Posts: 8
Joined: Sun Jun 18, 2023 9:53 pm
Home club or Range: VAA
Contact:

Re: Martini Henry

#9 Post by Martiniman »

Well played 👍👍
User avatar
Vossie
Posts: 277
Joined: Mon Oct 30, 2017 2:53 pm
Home club or Range: Bisley
Location: South East
Contact:

Re: Martini Henry

#10 Post by Vossie »

Martiniman wrote: Wed Nov 15, 2023 10:48 pm Well played 👍👍
Thank you Martiniman, it was a case of whatever could be done had to be done.
To own one is a privilege, to shoot is a blessing and to be able to pass it on is must.
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests