Case chamfer
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
- Blackstuff
- Full-Bore UK Supporter
- Posts: 7791
- Joined: Sun Nov 07, 2010 1:01 pm
- Contact:
Case chamfer
Hello all,
Its been quite a while since i've had to do any case prep so i'm a little rusty with certain elements so looking for opinions.
I use a Lee Quick Trim Power case trimmer that trims, chamfers and de-burs cases in one go. It could've been 4 years since I last used it. I have attached some pics of the results. Am I the only one that thinks the external chamfer on the case mouth is a bit excessive or would you be happy with it? They're .308Win cases.
Its been quite a while since i've had to do any case prep so i'm a little rusty with certain elements so looking for opinions.
I use a Lee Quick Trim Power case trimmer that trims, chamfers and de-burs cases in one go. It could've been 4 years since I last used it. I have attached some pics of the results. Am I the only one that thinks the external chamfer on the case mouth is a bit excessive or would you be happy with it? They're .308Win cases.
DVC
- Blackstuff
- Full-Bore UK Supporter
- Posts: 7791
- Joined: Sun Nov 07, 2010 1:01 pm
- Contact:
-
- Full-Bore UK Supporter
- Posts: 742
- Joined: Thu Jun 07, 2012 7:26 pm
- Contact:
Re: Case chamfer
Remember that the Quick Trim cutter is adjustable, make sure that it is set to its minimum, turn the knurled ring clockwise when viewed from the blade end until it stops.
According to the Lee instructions, this will trim to .006 below nominal case length.
Lee states you can trim the case shorter by turning the ring a click at a time anti-clockwise, which will remove approximately .001 per click up to a maximum of 10 clicks.
ukrifleman
https://www.reloading.co.uk/lee-quicktrim.html
According to the Lee instructions, this will trim to .006 below nominal case length.
Lee states you can trim the case shorter by turning the ring a click at a time anti-clockwise, which will remove approximately .001 per click up to a maximum of 10 clicks.
ukrifleman
https://www.reloading.co.uk/lee-quicktrim.html
- Mauserbill
- Full-Bore UK Supporter
- Posts: 1135
- Joined: Thu Jun 22, 2017 4:49 pm
- Home club or Range: Range
- Contact:
Re: Case chamfer
Hello
Like UKR says it is adjustable, I use them on all my military cases, and results are excellent, no more faffing about with the usual case prep tools.
Like UKR says it is adjustable, I use them on all my military cases, and results are excellent, no more faffing about with the usual case prep tools.
Re: Case chamfer
Pictures shouldn't be necessary to answer this. For me, *any* outside chamfer is too much. Inside chamfer is sometimes applied, primarily to prevent bullet shaving. If trimming leaves a burr on the outside, then the outside should be deburred. Chamfering the outside is just weakening the case mouth for no good reason.Blackstuff wrote: ↑Tue May 09, 2023 9:03 amAm I the only one that thinks the external chamfer on the case mouth is a bit excessive or would you be happy with it?
My trimmer cuts the mouth completely square and practically burr free. I don't touch the outside, aside from any effect that tumbling-off the lube might have. I usually apply a very light flare instead of chamfering, but with jacketed bullets and neck ID 0.001" to 0.002" under bullet diameter, I could happily load without chamfer or flare and still not see shaving.
- Blackstuff
- Full-Bore UK Supporter
- Posts: 7791
- Joined: Sun Nov 07, 2010 1:01 pm
- Contact:
Re: Case chamfer
Thanks for the replies gents. I was aware that its adjustable, however whether its all the way one way or the other the result is the same.
Its so frustrating not being able to show the photos, but basically it seems dependent on how hard i press on the cutter as to how much chamfer goes on.
I am using the die in a Breech Lock Quick Change bushing, so I don't know if thats the problem? I would've thought that would have the opposite effect though. I'll give it a try out of there and see what happens.
Its so frustrating not being able to show the photos, but basically it seems dependent on how hard i press on the cutter as to how much chamfer goes on.
I am using the die in a Breech Lock Quick Change bushing, so I don't know if thats the problem? I would've thought that would have the opposite effect though. I'll give it a try out of there and see what happens.
DVC
- billgatese30
- Posts: 406
- Joined: Wed May 02, 2012 4:40 pm
- Home club or Range: Bishop Auckland & District Gun Club...and anywhere that will have me.
- Location: County Durham
- Contact:
Re: Case chamfer
I would have thought it will only take a thou or two of flex to make a big difference visually. Consistent pressure is likely to be a help. As said above, I only put enough inside chamfer to prevent shaving and as little as possible externally to keep as much brass in place as possible.
Chris
- phaedra1106
- Posts: 3413
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Case chamfer
If you want to pop round and let me take a look at them just give me a shout.
I'm out tonight and tomorrow night but should be in Friday most of the day
I'm out tonight and tomorrow night but should be in Friday most of the day
There's room for all Gods creatures, next to the mash and gravy :)
Re: Case chamfer
I dont think I have ever chamfered the outside of any cases in all the time I have been shooting. I am not sure I have ever chamfered the inside of a case either. Why would you want to thin the cases.
I use a L.E. Wilson trimmer that cuts the case mouths with no chamfer it just cuts them square I just run a deburing tool round the case mouths to get rid of any rags.
I have expanded case mouths to accept cast bullets but I normally use NOE expanders or a set of macined expanders I aquired from David/Christel.
I use a L.E. Wilson trimmer that cuts the case mouths with no chamfer it just cuts them square I just run a deburing tool round the case mouths to get rid of any rags.
I have expanded case mouths to accept cast bullets but I normally use NOE expanders or a set of macined expanders I aquired from David/Christel.
Re: Case chamfer
Yup just use a Lyman case trimmer when needed and then just run a Lyman deburring tool around inside and out to remove any burred edges.
https://www.reloading.co.uk/lyman-chamf ... -tool.html
Can't see the need to chamfer any of the brass.
https://www.reloading.co.uk/lyman-chamf ... -tool.html
Can't see the need to chamfer any of the brass.
Never argue with an idiot, he will drag you down to his level and beat you with experience.
Who is online
Users browsing this forum: No registered users and 1 guest